Anker Soundcore Space One | Active Noise Cancelling Headphones - Latte Cream

Anker Soundcore Space One | Active Noise Cancelling Headphones – Latte Cream How to Switch Ambient Sound Modes 1. Space One automatically sets the default ANC and Transparency levels are both set to 5. These levels can be adjusted through the soundcore app according to personal preference. 2. Pressing the NC button once will switch between noise canceling and transparency modes by default. You can add “normal mode” through the soundcore app, after this, you can press the NC button to cycle through noise canceling, transparency, and normal modes. How to Reset To reset the Space One back to factory settings, turn on the headphones and then press and hold the power button and volume up button for 5 seconds. The power indicator light will flash slowly three times in red, indicating that the headphones have been reset to factory settings successfully. Note: After restoring to factory settings, all function switches will be restored to their default settings. For example, after restoring to factory settings, the wear detection function will be restored to the default closed state. Please reset the function switches according to personal usage habits. How to Switch to BassUp Mode 1. The “Controls” section of the soundcore app allows you to set the double-tap NC button to activate the BassUp feature. After setting, you can experience the BassUp effect by double-tapping the NC button. 2. You can also select the Bass Booster EQ in the soundcore app to experience the BassUp effect. How to Enable the Wear Detection Function The automatic play/pause feature (Wearing Detection) is turned off by default. Please remove the dustproof sticker on the sensor detection hole inside the left earpads. Enable the “Wearing Detection” in the upper right corner of the soundcore app to activate the Wearing Detection feature. Wearing Calibration Related 1. If the Wearing Detection function is not sensitive enough, you can use the wearing calibration feature to improve the sensitivity of the wearing detection. 2. Calibration method: You can perform wearing calibration in the “Wearing Detection” section of the soundcore app’s settings menu by following the prompts to restore detection sensitivity. To avoid calibration failure, please pay close attention to the place/wearing guide provided in the souncore app. How to do Firmware Upgrades 1. You can upgrade the headphone firmware through a pop-up window in the soundcore app. 2. You can also upgrade the firmware in the “Update Firmware” section of the soundcore app’s settings menu Call Control 1. Press the play/pause button once to answer a call 2. Press the play/pause button once to end a call 3. Press and hold the play/pause button for 2 seconds to reject an incoming call 4. During a call, press and hold the play/pause button for 2 seconds to toggle between the mute and unmute states. A prompt tone will indicate a successful switch. Bluetooth Indicator and Prompt Tone Related Information 1. Power on: Power on tone, battery level voice prompt, power indicator flashes white 3 times and then turns off. 2. Power off: Power off tone, power indicator flashes white 3 times and then turns off. 3. Bluetooth pairing mode: Enters pairing mode with a prompt tone, power indicator flashes blue. 4. Bluetooth pairing success: Bluetooth pairing success tone, power indicator stays on for 3 seconds and then turns off. 5. Bluetooth disconnection: Bluetooth disconnected tone, no light effect. 6. Reconnection mode: Prompt tone, power indicator flashes slowly in blue. Battery Level Indicator and Prompt Tone Related Information 1. Half an hour before the battery is depleted: Power indicator flashes once every 20 seconds. 2. Charging: Power indicator stays on in red. 3. Fully charged: Power indicator turns off. 4. Battery level below 10%: Power-on prompt for low battery level. 5. Battery level between 31% and 69%: Power-on prompt for medium battery level. 6. Battery level above 70%: Power-on prompt for high battery level. Play-time Related Tested battery life data for playing specified music on iPhone at 50% volume: 1. ANC: 40 hours 2. Transparency: 40 hours 3. Normal: 55 hours 4. Fast Charge 5 min: 4 hours under Normal mode.